What are you looking for?

Your cart

No Login?

SpeedyBee F405 Mini BLS 35A 20x20 Stack

  • Availability:In Stock
  • Ex Tax: $31.99


Global Shipping     60-days Warranty     7-days Refund

Earn Maker Coins to get cash discounts when buying this product.

Description

Specification

Product NameSpeedyBee F405 Mini BLS 35A 20x20 Stack
Flight ControllerSpeedyBee F405 Min
ESCSpeedyBee BLS 35A Mini V2 4-in-1 ESC
BluetoothSupported. Used to connect with the SpeedyBee App for flight controller and ESC parameter configuration. Please make sure the MSP switch on UART 4 is turned on and set to a baud rate of 115200, otherwise Bluetooth functionality will not be available.
WiFiNOT Supported
Wireless FC Firmware FlashingNOT Supported
Wireless Blackbox Dwonload & AnalysisNOT Supported
Power Input3-6S LiPo
Mounting20 x 20mm 3.5mm hole size,Compatible with M2 and M3 screws/Silicone grommets
Dimension32mm(L) x 35mm(W) x 14.2mm(H)
Weight13.5g
ProductNameSpeedyBee F405 V3 30x30 Flight Controller
MCUSTM32F405
IMU(Gyro)ICM42688P
USB Port TypeType-C
BarometerBuilt-in
OSD ChipAT7456E chip
BLE BluetoothSupported. Used to connect with the SpeedyBee App for flight controller and ESC parameter configuration. Please make sure the MSP switch on UART 4 is turned on and set to a baud rate of 115200, otherwise Bluetooth functionality will not be available.
Wireless FC Firmware FlashingNOT Supported. Please connect to the Betaflight configurator on the PC to do FC firmeare update
Wireless Blackbox Dwonload & AnalysisNOT Supported. Please connect to the Betaflight configurator on the PC to do blackbox analysis.
WIFINot supported
DJI Air Unit Connection WayDirect soldering
DJI Air Unit CompatibilityCompatible with all DJI Air Units: DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1. Please use the solder pads < 9V, G, T1, R1, G, SUBS(R2) > on the front right corner of the flight controller to make a pin-to-pin connection with the solder pads on the DJI Air Unit. UART1(T1, R1) is used for OSD and SUBS(R2) is used for DJI Air Unit’s internal SBUS receiver signal input.
Blackbox8MB Onboard Flash
BetaFlight Camera Control PadYes(CC pad on the front side)
Current Sensor InputSupported. For SpeedyBee BLS 35A V2 ESC, please set Scale=250 and Offset=-500.
Power Input3-6S LiPo. The flight controller is powered through the G, V wires of the 8pin harness or G, V pads from the bottom side of the flight controller.
5V Output4 groups of 5V output, three +5V pads and 1 BZ+ pad( used for Buzzer) on front side. The total current load is 2A.
9V Output1 group of 9V output, one +9V pad on front side. The total current load is 3A.
3.3V OutputSupported. Soldering pad named ‘3V3’ on the front top of the flight controller. Designed for 3.3V input receivers. Up to 500mA current load.
4.5V OutputSupported. Designed for radio receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.
ESC SignalM1 - M4 wires or soldering pads on bottom side.
UART6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6
ESC TelemetryUART R5(UART5)
I2CSupported. DA & CL pads on front side. Used for magnetometer, sonar, etc
Traditional Betaflight LED PadSupported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LEDs controlled by the Betaflight firmware.
BuzzerBZ+ and BZ- pad used for 5V Buzzer
BOOT ButtonSupported. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.
RSSI InputNot Supported
Smart Port / F.PortNot Supported
Supported Flight Controller FirmwareBetaFlight(Default), INAV
Firmware Target NameSPEEDYBEEF405MINI
Mounting20 x 20mm 3.5mm hole diameter ,Compatible with M2 and M3 screws/Silicone grommets.
Dimension30(L) x 32(W) x 7.8(H)mm
Weight9.6g
Product Name
SpeedyBee 35A BLHeli_S Mini V2 4-in-1 ESC
FirmwareBLHeli_S J-H-40
Continuous Current35A * 4
Burst Current45A(5seconds)
ESC ProtocolDSHOT300/600
Power Input3-6S LiPo
Power OutputVBAT(Battery voltage, used to power the flight controller)
Current SensorSupport (Scale=250 Offset=-500)
ESC TelemetryNot supported
Mounting20 x 20mm ∅3.5mm hole size,compatible with M2 and M3 screws/Silicone grommets.
Dimension35 * 35 * 5.5mm
Weight7.2g
SpeedyBee F405 V3 STACK
$59.99 for a Bluetooth 35A Stack? That’s ridiculous!
Utilizing an upgraded F405 flight controller chip with better performance than the F411, it features a built-in Bluetooth chip for seamless wireless Betaflight tuning. The board comes with a 4-level battery voltage display, built-in barometer, and supports connectivity to all DJI Air Units. It offers 4 available UART ports, and a dual BEC setup with 5V 2A and 9V 3A outputs.
35A 4-in-1 BLHeliS Mini ESC: This ESC provides four synchronized outputs with a continuous current of 35A, delivering strong power to drive all 2-4 inch and lightweight 5-inch quadcopters via 4-6S battery. Equipped with a TVS transient suppression diode onboard, it better absorbs surge voltage, providing enhanced protection for the ESC.
SpeedyBee F405 V3 STACK
Tune Flight controller and ESC wirelessly!
Power the quad, connect the SpeedyBee app via Bluetooth, configure the UART Ports,PID,OSD and every other settings on this flight controller. Also, every parameter of the BLHeli_S ESC in this stack can be set via the app.
With this Bluetooth stack, even micro drones become easy to tune—no need to worry about the hassle of inserting USB cables into the flight controller. Simply tune your drone wirelessly through the App, and say goodbye to wires and worries!
SpeedyBee F405 V3 STACK
Powerful Real 35A 4-in-1 ESC!
6-layer 2oz PCB plus optimized circuit design equals stable and strong current output. The four-channel continuous 140A output can reach 30 seconds*.
The use of Japanese TDK filtering SMT capacitors and the onboard TVS protective diode, further enhances your flight experience, providing a seamless and reliable performance. The stack underwent rigorous pressure testing with various 5-inch freestyle and racing drones, confirming its powerful capability to effortlessly drive any 2-4 inch and lightweight 5-inch drones.
SpeedyBee F405 V3 STACK
Clean Gyroscope Power Supply, Smoother Flight
Equipped with the renowned brand MaxLinear's LDO power supply chip, the gyroscope receives independent power, boosting surge protection capacity by 320%. Additionally, built with a 100uF ultra-large filtering tantalum capacitor, guarding the gyroscope's data from interference caused by the power source. Each posture and movement during flight receives precise responsiveness, allowing you to fully experience the pure beauty of flying!
SpeedyBee F405 V3 STACK
Forgot your LiPo checker? Just look at the FC!
On the side of the flight controller, you will find a 4-level battery capacity indicator. As soon as you connect the battery, you can instantly see the battery level, saving you the hassle of needing to put on goggles to check the battery status.
SpeedyBee F405 V3 STACK
Change motor directions wirelessly!
Are you still using a computer to change motor directions? With this stack, when you finish your build, connect to the SpeedyBee app, change the motor directions just in a few simple steps*. Then take off.
* To use this feature, go to the App > Motors > Motor Direction Settings.
SpeedyBee F405 V3 STACK
Support DJI Digital Video Transmitter
The flight controller has two independent 9V 3A BEC and 5V 2A BEC, supports various analog image transmissions above 5V, and also supports DJI O3 Air Unit/Link / Vista/Air Unit V1
SpeedyBee F405 V3 STACK
M2 or M3? Why not both?
Have you ever experienced that the stack holes of your frame did not fit the stack you got? This stack is perfectly compatible with M2/M3 screws. What’s more, two sets of M2 and M3 screws + silicone grommets are included in the package!
SpeedyBee F405 V3 STACK
TVS Protective Diode + 470uF Low-ESR Capacitor = Upgraded ESC Protection
The ESC is built with TVS protective diode to absorb the voltage spike when you plug in the battery, or during crashes that block your props. We also provide a Rubycon 470uF Low-ESR capacitor, ensuring clean data from the gyro to the FC.
SpeedyBee F405 V3 STACK
And packaged with more useful features
 Sufficient 4 x UARTs for your receiver + VTX + camera + GPS.
 Two independent 5V 2A BEC and 9V 3A BEC.
 Power your GPS with a USB cable - no battery needed. No extra heat, no worries
 17mm cutouts for FPV camera in your tight build
 Onboard barometer for real-time altitude sensing
 Onboard 8MB Blackbox storage
SpeedyBee F405 V3 STACK
SpeedyBee F405 V3 STACK
SpeedyBee F405 V3 STACK
SpeedyBee F405 V3 STACK
SpeedyBee F405 V3 STACK
SpeedyBee F405 V3 STACK
SpeedyBee F405 V3 STACK
SpeedyBee F405 V3 STACK
SpeedyBee F405 V3 STACK

Reviews (0)

Customer Reviews

Based on 0 reviews