What are you looking for?

Your cart

No Login?

SpeedyBee F405 V3 30x30 Flight Controller

  • Availability:In Stock
  • Ex Tax: $40.99


Global Shipping     60-days Warranty     7-days Refund

Earn Maker Coins to get cash discounts when buying this product.

Description

Specification

Product NameSpeedyBee F405 V3 30x30 Flight Controller
MCUSTM32F405
IMU(Gyro)BMI270
USB Port TypeType-C
BarometerBuilt-in
OSD ChipAT7456E chip
BLE BluetoothSupported. Used to connect with the SpeedyBee App for flight controller and ESC parameter configuration. Please make sure the MSP switch on UART 4 is turned on and set to a baud rate of 115200, otherwise Bluetooth functionality will not be available .
WIFINot supported
DJI Air Unit Connection WayTwo ways supported: 6-pin connector or direct soldering.
6-pin DJI Air Unit PlugSupported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.
Blackbox MicroSD Card Slot*Betaflight firmware requires the type of the microSD card to be either Standard (SDSC) or High capacity (SDHC), so extended capacity cards (SDXC) are not supported(Many high-speed U3 cards are SDXC). Also the card MUST be formatted with the FAT16 or FAT32 (recommended) filesystems. So, you could use any SD card less than 32GB, but the Betaflight can only recognize 4GB maximum. We suggest you use this 3rd party formatting tool and choose 'Overwrite format' then format your card. Also check out here for the recommended SD cards.
BetaFlight Camera Control PadYes(CC pad on the front side)
Current Sensor InputSupported. For SpeedyBee BLS 50A ESC, please set scale = 386 and Offset = 0.
Power Input3-6S LiPo. The flight controller is powered through the G, V wires of the 8pin cable or G, V pads from the bottom side of the flight controller.
5V Output9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 4x LED 5V pads. The total current load is 2A.
9V Output2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 2A.
3.3V OutputSupported. Designed for 3.3V-input receivers. Up to 500mA current load.
4.5V OutputSupported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.
ESC SignalM1 - M4 on bottom side and M5-M8 on front side.
UART6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection), UART5(Dedicated for ESC telemetry),UART6
ESC TelemetryUART R5(UART5)
I2CSupported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc.
Traditional Betaflight LED PadSupported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.
BuzzerBZ+ and BZ- pad used for 5V Buzzer
BOOT ButtonSupported.
[A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.
[B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.
RSSI InputSupported. Named as RS on the front side.
Smart Port / F.PortNot supported
Supported Flight Controller FirmwareBetaFlight(Default),INAV (INAV firmware can only use Multishot (recommended) and OneShot125. Please note that DShot is not supported.)
Firmware Target NameSPEEDYBEEF405V3
Mounting30.5 x 30.5mm( 4mm hole diameter)
Dimension41.6(L) x 39.4(W) x 7.8(H)mm
Weight9.6g

Manualhttps://store-fhxxhuiq8q.mybigcommerce.com/product_images/img_SpeedyBee_F405_V3_Stack/20230725-SpeedyBee_F405_V3_Stack_Manual_EN.pdf

SpeedyBee F405 V3 STACK
$69.99 for a Bluetooth 50A
Stack? That's ridiculous
I know right? With only $69.99, you will get an STM32F405 FC
(better than F411), onboard 4-level battery life indicator, 4GB
Blackbox SD card slot for your flight logs, 4 groups of LED strip pads,
complete with a DJI plugfor your digital quad, and built-in Bluetooth
for wireless configuration on the SpeedyBee app.
Don't forget about the powerful 50A 4-in-1 ESC, built with TVS
protective diode + Japan made TDK SMT capacitors + external
1000uF low ESR capacitor, everything is for durable build and
smooth flight.
All of that for only $69.99! Top-shelf spec at a crazy low price, what
are you waiting for?
* The DJI Air Unit plug is completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.
SpeedyBee F405 V3 STACK
Configure your FC and ESC
via Bluetooth
With SpeedyBee app, turn your phone into an all-in-one
FC configurator and tune your quad anytime, anywhere.
Experience wireless, fully configurable ESC experience with
SpeedyBee app.
SpeedyBee F405 V3 STACK
Powerful Real 50A 4-in-1 ESC!
Built with the robust BB21 MCU and large motor pads for easy
soldering. Built with Japan made TDK filtering SMT capacitors +
onboard TVS protective diode, brings smooth flight experience.
Real 50A output, ready for your baddest 6S motors.
SpeedyBee F405 V3 STACK
Forgot your LiPo checker?
Just look at the FC!
Built with a 4-level LED battery indicator, now you can fly
anywhere worry-free - even without your lipo checker!
 

* 1 light constantly on: battery level 10-25%

1 light blinking: battery level < 10%

SpeedyBee F405 V3 STACK
8 motors output for X8/Y6/
fixed-wings
You could use this stack to build your X8 drones, Y6 drones or
fixed wings. Forget about crawling through your massive build
just to plug in that USB cable. Just take out your phone to
configure everything in the SpeedyBee app.
SpeedyBee F405 V3 STACK
Change motor directions
wirelessly!
Finishing your latest build? Just replaced your motor after a crash?
Take your smartphone out, and configure your motor direction
wirelessly with the latest SpeedyBee app. Works for all
BLHeli32 / BLHeli_S / BlueJay ESCs.
SpeedyBee F405 V3 STACK
4 sets of LED pads with
simple switching
Need more visibility at night? Just solder up your LED strips*
and blaze the darkest trail you can find. With just one tap on t
he BOOT button, you can cycle through all different LED presets**
and pick the one you love!
* LED strips could be purchased here
**Or long press the boot button to switch to Betaflight LED mode
SpeedyBee F405 V3 STACK
1000uF Low ESR capacitor +
TVS protective diode =
Extra protection
The ESC is built with TVS protective diode to absorb the voltage
spike when you plug in the battery, or during crashes that block
your props.We also provide a humongous 1000uF low ESR
capacitor, ensuring clean data from the gyro to the FC.
SpeedyBee F405 V3 STACK
And packaged with more
useful features
● Built-in barometer for accurate height calculation
● SD Card slot can support up to 4GB Blackbox data*
● Dedicated DJI Air Unit connector for a quick digital build
● 9V 2A + 5V 2A individual BECs
● 4 x UARTs for your receiver + VTX + camera + GPS.
● Power your GPS with a USB cable - no battery needed.
   No extra heat, no worries.
● 22mm cutouts for FPV camera in your tight build
*Betaflight firmware requires the type of the microSD card to be
either Standard (SDSC) or High capacity (SDHC), so extended
capacity cards (SDXC) are not supported(Many high-speed U3 cards
are SDXC). Also the card MUST be formatted with the FAT16 or FAT32
(recommended) filesystems. So, you could use any SD card less than
32GB, but the Betaflight can only recognize 4GB maximum.
We suggest you use this 3rd party formatting tool and choose
'Overwrite format' then format your card. Also check out here for
the recommended SD cards .
SpeedyBee F405 V3 STACK
Dimensions
SpeedyBee F405 V3 STACK
Wiring Diagram
SpeedyBee F405 V3 STACK
Note: When using both a receiver and an Air Unit (including a direct connection using a ribbon cable) on the F405 V3 flight controller, there is an issue. This arises because the built-in SBUS receiver on the Air Unit and the external receiver are both connected to the Rx2 pad(SBUS pad) on the flight controller. As a result, the external receiver cannot be recognized properly by the flight controller. To resolve this, it is necessary to disconnect the SBUS wire from the Air Unit or connect the external receiver to the Rx3 pad on the UART3 port.
It is known that SBUS receivers and part of the ELRS receivers conflict with the built-in receiver on the Air Unit in the F405 V3 flight controller.Even ELRS reciver has this issue, but TBS reciver will not affected by this issue.
SpeedyBee F405 V3 STACK
 
SpeedyBee F405 V3 STACK
 
SpeedyBee F405 V3 STACK
 
SpeedyBee F405 V3 STACK
 
SpeedyBee F405 V3 STACK

Reviews (0)

Customer Reviews

Based on 0 reviews