Description
Description
- We’re glad to launched our new Mobula7 drone , this time the 75mm whoop based on 1s power. Thanks to the new AIO flight controller and the new third-generation RS0802 brushless motor, the new Mobula7 1s Will be the best choice in the whoop season.
- The world first 5-IN-1 AIO flight controller with ExpressLRS 2.0 , OPENVTX(up to 400mw), 12A Brushless Blheli_S ESC and Betaflight OSD coming out recently. This is amazing flight controller for Brushless whoop. You could get unbelievable RX and VTX range by using this flight controller.
- The new RS0802 motors comes with a new unibell design, use 1.5mm shaft and include PCB bottom plate, high efficiency and much more reliable.
- New onboard OpenVTX , max power up to 400mw, provide RCE and PIT mode, it was very useful for race event.
Features:
- X12 5-IN-1 AIO flight controller built-in 2.4G ELRS V2.0 and Openvtx
- VTX Power up to 400mw
- ELRS V2.0 Support
- NEW RS0802 KV20000 motors
- Runcam Nano3 The lightest 1/3 CMOS 800TVL Camera
- Smooth and powerful
- Compatible for 1S Lipo/LIHV
- Recommend 1S 450mah/550mah/650mah battery(Not include)
Specifications:
- Brand Name: Happymodel
- Item Name: Mobula7 1S 75mm Micro FPV whoop drone
- Wheelbase: 75mm
- Size: 99mm*99mm*40mm
- Weight: 24g
Receiver option:
- 2.4G ELRS SPI
- SPI Frsky D8/D16 not compatible with EMAX E6 radio
- PNP (without onboard receiver)
- TBS version(with external TBS CRSF NANO RX)
PNP Version(without onboard receiver)
- Full UART1 for external Receiver
- Support CRSF/GHOST/SBUS/IBUS/DSMX protocol
- IR1 pad(invert RX1) used for SBUS input
- Mode: RS0802 KV20000
- Configu-ration:9N12P
- Stator Diamter:8mm
- Stator Length:2mm
- Shaft Diameter:Φ1.5mm
- Motor Dimension(Dia.*Len):Φ10.5mm*13.5mm
- Weight(g):2.0g
- No.of Cells(Lipo):1S only
Propellers
- Weight:0.24g
- Material:PC
- Pitch:1 inchProps Dia:40mm
- Center Thickness:5mm
- Center Hole Dia:1.5mm
Flight controller
- X12 ELRS V1.0 flight controller built-in ELRS 2.4G receiver Target: CRAZYBEEF4SX1280
- X12 Frsky V1.0 flight controller built-in SPI Frsky 2.4G receiver Target: CRAZYBEEF4FR
- X12 PNP V1.0 flight controller with external TBS CRSF Nano receiver Target: CRAZYBEEF4DX
- X12 PNP V1.0 flight controller without onboard receiver Target: CRAZYBEEF4DX
- MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
- Sensor: MPU6000 or ICM20689 or BMI270(SPI connection)
- Mount hole size: 25.5mm*25.5mm
- Power supply: 1S battery input (DC 2.9V-4.35V)
- Built-in 12A(each) Blheli_S 4in1 ESC
- Built-in Betaflight OSD(SPI Control)
- Built-in 5.8G OpenVTX 0mw~400mw
- Built-in ExpressLRS 2.4G,Frsky D8/D16
- Built-in voltage detection
- Built-in current sensor
Onboard 4in1 ESC
- Power supply: 1S LiPo/LiPo HV
- Current: 12A continuous peak 15A (3 seconds)
- Support BLHeliSuite programmable
- Factory firmware: Z_H_30_REV16_7.HEX
- Default protocol: DSHOT300
- Support Bluejay firmware
- When use Blujay firmware with 48khz, should set startup power to 1100/1200
Onboard SPI ExpressLRS 2.4GHz Receiver
- Packet Rate option: 50Hz/150Hz/250Hz/500Hz
- ExpressLRS Firmware version: V2.0
- RF Frequency: 2.4GHz
- Antenna : SMD antenna
- Telemetry output Power: <12dBm
- Receiver protocol: SPI ExpressLRS
- Compatible with ExpressLRS V2.0 TX Module
- Couldn’t flash separately ExpressLRS firmware
Onboard Frsky SPI D8/D16 receiver Version
- SPI BUS receiver Frsky D8 compatible
- Compatible Non EU transmitter D8 modelChannels: 8ch
- No ground interference ( Transmitter and receiver 1 m from the ground): 200meterFailsafe support
Onboard 5.8g OPENVTX
- Firmware version: OPENVTX
- Smartaudio v2.1
- PIT Mode support
- RCE Mode support
- Channels:48ch
- Transmitting Power: 0/RCE/25mw/100mw/400mw
- Power supply: DC 5V
- Current (5v):650ma~1000ma
Runcam Nano3
- Model: RunCam Nano 3
- Image Sensor: 1/3″ CMOS
- Horizontal Resolution: 800TVL
- Lens : 2.1mm(M8) FOV 150°
- Signal System: NTSC
- S/N Ratio: >50dB
- Electronic Shutter Speed: Auto
- Auto Gain Control (AGC): Auto
- Min. Illumination: 0.01Lux@1.2F
- D-WDR: Auto
- Day/Night: Color
- Power:DC 3-5.5V
- Current: 110mA@5V 120mA@3.3V
- Housing Material: ABS
- Net Weight: 1.2g
- Dimensions: L14mm*W14mm*H9mm
Package includes:
- 1 x Mobula7 1S 75mm whoop Drone Frame (Mobula7 v4 frame)
- 1 x X12 ELRS V1.0 flight controller built-in SPI ELRS 2.4G receiver / X12 Frsky V1.0 flight controller built-in SPI Frsky 2.4G receiver / X12 PNP V1.0 flight controller with External TBS NANO receiver / X12 PNP V1.0 flight controller without onboard receiver (Optional)
- 4 x RS0802 KV20000 brushless motor
- 1 x Gemfan 1610-2 bi-blade propellers(4cw+4ccw)
- 1 x Runcam Nano3 1/3 CMOS 800TVL camera
- 1 x Onboard 5.8G Openvtx 0mw~400mw VTX
- 1 x 1S parallel charging board
- 1 x Propeller disassemble tool
- 1 x Extra camera canopy
